Snapmaker SnapDryer (by Polymaker)

Snapmaker

Snapmaker SnapDryer (by Polymaker)

1 spool · humidity sensor · prints while drying · 24 h timer

Not tested by Nick

Specs

Spools at once1
Prints while dryingYes
Humidity displayYes
Power68 W
Timer up to24 hours

From Snapmaker's own pages. A spec Snapmaker does not confirm is left out.

What it can dry

The SnapDryer (by Polymaker) does not state a max heat, so it is not matched to the drying chart.

Source: Bambu Lab Wiki: Drying filament, the fan oven column.

About the SnapDryer (by Polymaker)

The Snapmaker SnapDryer is Snapmaker's version of Polymaker's PolyDryer. Snapmaker says it is based on a design by Polymaker and FabNotion, keeps the same main function, adds parts for Snapmaker printers, and is fully compatible with the PolyDryer system. It is a heated Dry Dock under a sealed SnapDryer Box that holds one spool, and one dock can serve several boxes. It suits Snapmaker owners first, and anyone who wants filament dried and stored in the same box.

Which printers it works with

Snapmaker says it works with its 2.0, Artisan and J1 and J1s printers, and with other brands' printers that take 1.75 or 2.85 mm filament. Snapmaker's own printers take 1.75 mm only. Its support site also has a guide to using it with the Snapmaker U1. The Snapmaker extras are a 1500 mm filament tube, a filament entry cover, a filament tube connector, a round clamp and a tape measure, and the quick start guide covers cutting the tube to length and fitting it on the 2.0, Artisan and J1 and J1s. Snapmaker handles after sales service itself.

How it feeds your printer

Snapmaker's FAQ says you can dry a spool before printing, or set Continuous Mode and dry while printing. Regular Mode runs for up to 24 hours and Continuous Mode runs until you stop it, and Snapmaker says not to leave it unattended in that mode. Snapmaker recommends feeding through the top cover when the box sits level with the printer, or through the side when it sits well above it, to keep bends in the tube to a minimum. Set the spool so the filament feeds toward the outlet, or it may meet resistance.

What to know before buying

The SnapDryer is set by power level and drying time, not by temperature. You pick a power level and a time from the chart in the quick start guide, which is based on samples left at 25°C and 70% humidity for five days. Supported materials are PLA, PETG, ABS, ASA, TPU, PA, PC, PVA and Breakaway support for PLA. The box takes spools up to 205 by 78 mm, which Snapmaker says fits all its own 1 kg spools and most other brands' 1 kg spools, with a spool roller for smaller ones. A hygrometer and a reusable desiccant that turns from orange to dark green sit in the box. In Snapmaker's test at 20°C and 60% humidity, the humidity inside the box changed by less than 5% in 30 days. Snapmaker also sells the box and the dock on their own.

Compare with similar dryers

The dryers nearest the SnapDryer (by Polymaker) on spools and max heat.

DryerSpoolsMax heatPrints while dryingPriceNick
SnapmakerSnapDryer (by Polymaker) This dryer1Not statedYes$71.99Not tested
SUNLUFilaDryer S2170°CYes$44.99Not tested
CrealitySpace Pi V2 Filament Dryer175°CUnconfirmed$66Not tested
EryoneSnail Dryer Box M2155°CYes$69.99Not tested
PolymakerPolyDryer173°CYes$79.99Not tested

Store prices as of Nov 17.

Compare every dryer

More reading