
Elegoo H1 HT Dryer Box
1 spool · up to 85°C · auto-rotating spool · prints while drying · 12 h timer
Not tested by Nick
Specs
| Spools at once | 1 |
|---|---|
| Max heat | 85°C |
| Prints while drying | Yes |
| Spool turns freely | Yes |
| Humidity display | Yes |
| Power | 130 W |
| Timer up to | 12 hours |
From Elegoo's own pages. A spec Elegoo does not confirm is left out.
What it can dry
The H1 HT Dryer Box heats up to 85°C. Here is how that meets Bambu Lab's fan oven chart.
Reaches
- PLA50°C
- PETG65°C
- TPU70°C
- ABS and ASA85°C
- PC85°C
- Nylon and carbon blends85°C
Source: Bambu Lab Wiki: Drying filament, the fan oven column.
About the H1 HT Dryer Box
The Elegoo H1 HT is a single spool filament dryer that heats to 85°C and turns the spool while it dries. It runs on its own, with no printer connection, and can feed a printer through a PTFE tube from either of its two rear outlets. It suits someone who dries one spool at a time and wants enough heat for ABS, ASA, PC and nylon as well as PLA and PETG.
Drying engineering filaments
Elegoo says 85°C meets the drying needs of common consumer filaments and some engineering filaments. The 11 presets cover PLA, PETG, TPU, ABS, ASA, PET, PP, PC, nylon (PA), a carbon fibre nylon and PVA. Each preset runs for 8 hours, at 55°C for PLA, 65°C for PETG, 70°C for TPU and ABS, and 80°C for the other seven. Custom Mode sets anything from 45 to 85°C and from half an hour to 12 hours. Elegoo's order of advice is the filament maker's own drying figures first, then the preset, then Custom Mode. For carbon fibre nylons it says to print soon after drying and reseal what's left.
Rotate drying is on by default. It turns the spool one notch every five minutes, roughly a full turn every 30 minutes, so the side away from the hot air outlet heats evenly too. Two active air valves vent moisture while it dries and close when it finishes.
How it feeds your printer
Elegoo says the H1 HT is designed to work with virtually all FDM printers, with no brand lock in. Its standard workflow is dry first, then print. To feed a printer straight from the dryer, screw in the pneumatic fitting, push in the PTFE tube from the box, then thread the filament, and switch spool rotation off. Elegoo recommends the upper outlet for TPU and other flexible filaments and for fibre reinforced filaments, because that path bends less, and the lower outlet for PLA, PETG, ABS and other common filaments. The spool has to sit so the filament leaves in the direction the rollers turn, or feed resistance goes up. Elegoo says you can try feeding an AMS, CFS or other multi material system that accepts an external spool through a PTFE tube, and that compatibility depends on that system.
What to know before buying
It takes 1.75 mm filament only, on spools 50 to 68 mm wide and up to 200 mm across, which covers common 1 kg spools. Elegoo says not to use 2 kg or 3 kg spools or filament without a spool. A 3.5 inch touch screen shows the chamber temperature and humidity, and lid detection pauses the heater while the lid is open. After drying the valves close, so a spool can stay inside for a short time, but Elegoo recommends a sealed bag or box with desiccant for longer storage. Leave at least 10 cm clear behind it for the exhaust. In Elegoo's lab it measured about 36 dB at most.
Compare with similar dryers
The dryers nearest the H1 HT Dryer Box on spools and max heat.
| Dryer | Spools | Max heat | Prints while drying | Price | Nick |
|---|---|---|---|---|---|
| ElegooH1 HT Dryer Box This dryer | 1 | 85°C | Yes | $80 | Not tested |
| Bambu LabAMS HT | 1 | 85°C | Yes | $119 | Not tested |
| CrealitySpace Pi V2 Filament Dryer | 1 | 75°C | Unconfirmed | $66 | Not tested |
| PolymakerPolyDryer | 1 | 73°C | Yes | $79.99 | Not tested |
| SUNLUFilaDryer S2 | 1 | 70°C | Yes | $44.99 | Not tested |
Store prices as of Nov 17.
More reading
- The best filament dryersNick's picks and how to choose one
- Filament deals: dryers and storageEvery dryer and storage item with today's price