
Polymaker
Polymaker PolyDryer
1 spool · up to 73°C · humidity sensor · prints while drying · 24 h timer
Not tested by Nick
Specs
| Spools at once | 1 |
|---|---|
| Max heat | 73°C |
| Prints while drying | Yes |
| Spool turns freely | Yes |
| Humidity display | Yes |
| Power | 68 W |
| Timer up to | 24 hours |
From Polymaker's own pages. A spec Polymaker does not confirm is left out.
What it can dry
The PolyDryer heats up to 73°C. Here is how that meets Bambu Lab's fan oven chart.
Reaches
- PLA50°C
- PETG65°C
- TPU70°C
Does not reach
- ABS and ASA85°C
- PC85°C
- Nylon and carbon blends85°C
Source: Bambu Lab Wiki: Drying filament, the fan oven column.
About the PolyDryer
The Polymaker PolyDryer comes in two parts: a heated Dry Dock and a sealed PolyDryer Box that holds one spool. The box sits on the dock to dry, then lifts off and keeps the spool sealed in storage, and Polymaker says one dock can serve as many boxes as you need. It was designed and developed with Polymaker's partner FabNotion. It suits someone who keeps several spools on the go and wants each one dried and stored in the same box.
Who it suits
The PolyDryer is built around storage as much as drying. Each box has a hygrometer and a desiccant that turns from orange to dark green as it takes on moisture, and the dock can dry that desiccant again at power level 3 in about 8 hours. Polymaker's wiki says the hygrometer reads down to 10%. The box is sold without the dock as well, so adding a spool means adding a box, and the dock is sold on its own too. Snapmaker sells a version as the SnapDryer, which it says is fully compatible with the PolyDryer system. Polymaker gives a one year warranty.
What to know before buying
Polymaker doesn't quote a single drying temperature. It says the temperature from its 360° airflow varies around the spool, that room temperature, spool size and material all change it, and that the highest range is 68 to 73°C. You choose one of three power levels and a time of up to 24 hours, or long press the power level button for Continuous Mode, which runs until you stop it. Polymaker says not to leave it unattended in that mode. The manual's chart runs from 6 hours for PLA, PETG, ABS and ASA up to 18 hours for PA and 24 hours for PVA, based on samples left at 25°C and 70% humidity for five days.
Polymaker lists PLA, PVB, PETG, ABS, ASA, TPU, PA, PC, PVA and its PolySupport filaments as supported, in 1.75, 2.85 and 3.00 mm. The box takes a spool up to 205 by 78 mm with its filament, which Polymaker says covers spools up to 1 kg. For bigger spools it sells the PolyDryer Box XL, which holds up to 3 kg and fits the dock with an optional adapter.
How it feeds your printer
The filament goes through the outlet plug before the spool goes in, and a 50 cm PTFE tube comes in the box. A central holder lets the spool rotate smoothly, and a spool roller is included for spools with damaged edges. The manual says to keep the filament wound tight or fed through the outlet while drying, so a loose end can't block the heating vent. When the box comes off the dock, the airlocks go back in to keep the seal.
Compare with similar dryers
The dryers nearest the PolyDryer on spools and max heat.
| Dryer | Spools | Max heat | Prints while drying | Price | Nick |
|---|---|---|---|---|---|
| PolymakerPolyDryer This dryer | 1 | 73°C | Yes | $79.99 | Not tested |
| CrealitySpace Pi V2 Filament Dryer | 1 | 75°C | Unconfirmed | $66 | Not tested |
| SUNLUFilaDryer S2 | 1 | 70°C | Yes | $44.99 | Not tested |
| ElegooH1 HT Dryer Box | 1 | 85°C | Yes | $80 | Not tested |
| Bambu LabAMS HT | 1 | 85°C | Yes | $119 | Not tested |
Store prices as of Nov 17.
More reading
- The best filament dryersNick's picks and how to choose one
- Filament deals: dryers and storageEvery dryer and storage item with today's price