Bambu Lab AMS HT

Bambu Lab

Bambu Lab AMS HT

1 spool · up to 85°C · humidity sensor · auto-rotating spool

Not tested by Nick

Specs

Spools at once1
Max heat85°C
Prints while dryingYes
Spool turns freelyYes
Humidity displayYes
Power150 W

From Bambu Lab's own pages. A spec Bambu Lab does not confirm is left out.

What it can dry

The AMS HT heats up to 85°C. Here is how that meets Bambu Lab's fan oven chart.

Reaches

  • PLA50°C
  • PETG65°C
  • TPU70°C
  • ABS and ASA85°C
  • PC85°C
  • Nylon and carbon blends85°C

Source: Bambu Lab Wiki: Drying filament, the fan oven column.

About the AMS HT

The Bambu Lab AMS HT is a single spool unit in Bambu's Automatic Material System that also dries filament, at up to 85°C. It connects to a Bambu Lab printer and feeds it automatically like any other AMS, and Bambu says it is made for high performance materials. It suits Bambu owners who print ABS, ASA, PC or nylon, and anyone adding slots to a Bambu multi material setup.

Which printers it works with

The AMS HT is made for Bambu Lab printers and connects to them with Bambu's 6 pin bus cable. Bambu's store says it is compatible with all of them, and its printer picker lists the A1, X1 and P1, P2S, H2S, H2D and H2C, X2D and A2 series. Bambu's connection guide also covers the H3C. What changes from printer to printer is the extra hardware, according to Bambu's wiki:

  • A1 series: the A1 Series AMS Hub, sold separately, and printer firmware 01.07.00.00 or later. An AMS lite can't be combined with other AMS units.
  • X1 and P1 series: a Filament Buffer for one unit or an AMS Hub for several, plus a PTFE tube coupler and a 4 pin cable. Up to four AMS HT units.
  • P2S: the P2S Combo includes a buffer, and a P2S bought on its own needs one. Up to four AMS HT units plus four AMS 2 Pro.
  • H2 series and X2D: the buffer is built in or included. Up to eight AMS HT units plus four AMS 2 Pro.

It can't dry on its own. Bambu says the AMS HT has to be connected to a powered printer by its 6 pin cable to dry, and that drying runs from its own power cord, which is in the box, never from the printer.

How it feeds your printer

A brushless servo motor drives the feed, and RFID tags on Bambu's own filament set the drying settings with no manual input. It takes 1.75 mm filament on spools 50 to 68 mm wide and 197 to 202 mm across. Soft or brittle filament goes out through a separate bypass outlet on the top cover. Bambu lists TPE, generic TPU and filaments with carbon or glass fibre for that outlet, and in that mode the AMS HT can't load or unload by itself, so you push the filament through to the extruder by hand.

Drying while printing depends on the printer. Bambu's wiki lists it for the H2D, H2S, P2S, X2D and A2L, each from a minimum firmware version, and says the P1S, P1P, X1C, A1 and A1 mini are not supported yet. Once a print starts, the system lowers the drying temperature by itself so the filament doesn't soften inside the AMS and get crushed by its feed gears.

Drying engineering filaments

Bambu's wiki says some engineering materials need more than the 65°C of the AMS 2 Pro and recommends the AMS HT for them. Bambu's store list of materials the AMS HT can dry includes ABS, ASA, PET, PA, PC, PP, POM and HIPS as well as PLA and PETG. The wiki says the heater holds 85°C even in a room as cool as 10°C, and electromagnetic vents open to push moist air out once the chamber is hot, then close to keep the spool sealed. In rotating mode the spool turns 30° every 5 minutes for even drying. A front screen shows humidity, temperature and the drying time left. Bambu also says some filaments need more than 85°C and may not dry completely, naming PPS and PPA.

Compare with similar dryers

The dryers nearest the AMS HT on spools and max heat.

DryerSpoolsMax heatPrints while dryingPriceNick
Bambu LabAMS HT This dryer185°CYes$119Not tested
ElegooH1 HT Dryer Box185°CYes$80Not tested
CrealitySpace Pi V2 Filament Dryer175°CUnconfirmed$66Not tested
PolymakerPolyDryer173°CYes$79.99Not tested
SUNLUFilaDryer S2170°CYes$44.99Not tested

Store prices as of Nov 17.

Compare every dryer

More reading