Creality Space Pi V2 Filament Dryer

Creality

Creality Space Pi V2 Filament Dryer

1 spool · up to 75°C · humidity sensor · 360° hot-air drying

Not tested by Nick

Specs

Spools at once1
Max heat75°C
Humidity displayYes

From Creality's own pages. A spec Creality does not confirm is left out.

What it can dry

The Space Pi V2 Filament Dryer heats up to 75°C. Here is how that meets Bambu Lab's fan oven chart.

Reaches

  • PLA50°C
  • PETG65°C
  • TPU70°C

Does not reach

  • ABS and ASA85°C
  • PC85°C
  • Nylon and carbon blends85°C

Source: Bambu Lab Wiki: Drying filament, the fan oven column.

About the Space Pi V2 Filament Dryer

The Creality Space Pi V2 is a one-spool dryer in Creality's Space Pi line. Creality lists it at up to 75°C, with 360° hot-air circulation, a second-generation smart sensor, and smart presets with touch control. It suits one printer and one spool at a time, for anyone who wants to dry PLA, PETG or TPU before a print.

Who it suits

The V2's 75°C covers the drying temperatures in Bambu Lab's chart for PLA, PETG and TPU. In a forced-air oven, Bambu Lab gives 50°C for PLA, 60 to 65°C for PETG and 70°C for TPU. For ABS, ASA, PC and nylon blends the same chart gives 75 to 85°C, so the V2 reaches only the bottom of that range. If those materials are most of what you print, a dryer that reaches 85°C is the safer choice.

With room for one spool, it fits a single printer, or someone who dries the next spool while the current one prints from a sealed box.

What to know before buying

The Creality details this page draws on don't confirm whether the V2 feeds a printer while it dries, how long its timer runs, or its power draw, so the spec table above leaves those rows out rather than guess. If you want to print straight from the dryer, check that on Creality's listing before you buy.

That makes storage after drying worth planning for. Bambu Lab's drying guide says that at around 55% humidity, freshly dried filament usually takes on enough moisture to affect print quality within 2 to 12 hours. It advises putting dried filament straight into a sealed container or an AMS with effective desiccant.

The V2 has a humidity sensor, so you can watch the humidity in the box while a spool dries. By Creality's figures it ships in a 315 by 125 by 300 mm package at 1,450 g gross.

The V2 or the V2 Plus

The V2 Plus holds two spools and the V2 holds one. Creality's highlights for the two read the same on 360° hot-air circulation, the second-generation smart sensor and the smart presets with touch control, and the Plus adds a new air duct design. Creality lists a 48-hour timer for the Plus, and the Plus can feed a printer while it dries. Neither is confirmed for the V2 in the details this page draws on.

Heat is the other thing to check. Creality gives the V2 up to 75°C. Its pages give two different top temperatures for the Plus, so if heat decides it for you, confirm the Plus's figure with Creality.

Compare with similar dryers

The dryers nearest the Space Pi V2 Filament Dryer on spools and max heat.

DryerSpoolsMax heatPrints while dryingPriceNick
CrealitySpace Pi V2 Filament Dryer This dryer175°CUnconfirmed$66Not tested
PolymakerPolyDryer173°CYes$79.99Not tested
SUNLUFilaDryer S2170°CYes$44.99Not tested
ElegooH1 HT Dryer Box185°CYes$80Not tested
Bambu LabAMS HT185°CYes$119Not tested

Store prices as of Nov 17.

Compare every dryer

More reading