
Eryone
Eryone Snail Dryer Box M2
1 spool · up to 55°C · humidity sensor · prints while drying · 5 h presets
Not tested by Nick
Specs
| Spools at once | 1 |
|---|---|
| Max heat | 55°C |
| Prints while drying | Yes |
| Humidity display | Yes |
| Timer up to | 5 hours |
From Eryone's own pages. A spec Eryone does not confirm is left out.
What it can dry
The Snail Dryer Box M2 heats up to 55°C. Here is how that meets Bambu Lab's fan oven chart.
Reaches
- PLA50°C
Does not reach
- PETG65°C
- TPU70°C
- ABS and ASA85°C
- PC85°C
- Nylon and carbon blends85°C
Source: Bambu Lab Wiki: Drying filament, the fan oven column.
About the Snail Dryer Box M2
The Eryone Snail Dryer Box M2 is a one-spool filament dryer in a compact, snail-shaped box. A fan inside circulates the heat, a built-in thermohygrometer reads the air in the box, and when the heater is off the box doubles as a place to store the spool. You can print from the spool while it dries, and the M2 suits a single printer that runs PLA most of the time.
Who it suits
The M2 tops out at 55°C. Bambu Lab's drying chart gives 50°C for PLA Basic in a forced-air oven, 60 to 65°C for PETG and 70°C for TPU. So this box covers PLA and stops short of PETG, TPU and the hotter engineering materials. It fits a printer that lives on PLA, or a second box that keeps one PLA spool ready beside a hotter dryer.
The letter in the name matters. Eryone's FAQ says the M1 keeps unsealed filament from getting wet but "cannot be heated and dried", while the M2 "can be moisture-proof or heat-drying". If you want to dry filament, the M2 is the one to look at.
What to know before buying
The M2 runs on three preset settings. Eryone's FAQ says the longest it will heat is 5 hours, after which it shuts itself off, and for a longer run you start it again. Eryone says you can repeat a run as often as you like. The display reads in degrees Celsius only.
- The fan is there so the heat circulates evenly, and Eryone placed the thermohygrometer away from the heater so it reads the temperature more precisely.
- It uses recyclable desiccant, which Eryone says can be dried on a 3D printer's heated bed.
- It takes 1.75 mm and 2.85 mm filament.
- Eryone rates it below 40 dB while heating and says the shell is made from fireproof ABS and PC.
- It runs on its own power cord, which comes in the box, not on USB.
Spool width is the one thing to check. Eryone's listing gives two different answers on the widest spool the box takes, so if your spools run wide, confirm the fit with Eryone before you buy.
Drying is only half the job. Bambu Lab's advice is to store moisture-sensitive filament in a sealed container or an AMS with effective desiccant as soon as it comes out of the dryer. With the M2, the spool can stay in the box after a run, since Eryone describes it as moisture-proof storage when it isn't heating.
Compare with similar dryers
The dryers nearest the Snail Dryer Box M2 on spools and max heat.
| Dryer | Spools | Max heat | Prints while drying | Price | Nick |
|---|---|---|---|---|---|
| EryoneSnail Dryer Box M2 This dryer | 1 | 55°C | Yes | $69.99 | Not tested |
| SUNLUFilaDryer S2 | 1 | 70°C | Yes | $44.99 | Not tested |
| PolymakerPolyDryer | 1 | 73°C | Yes | $79.99 | Not tested |
| CrealitySpace Pi V2 Filament Dryer | 1 | 75°C | Unconfirmed | $66 | Not tested |
| ElegooH1 HT Dryer Box | 1 | 85°C | Yes | $80 | Not tested |
Store prices as of Nov 17.
More reading
- The best filament dryersNick's picks and how to choose one
- Filament deals: dryers and storageEvery dryer and storage item with today's price