
EIBOS
EIBOS Polyphemus filament dryer
2 spools · up to 80°C · humidity sensor · auto-rotating spools · 24 h timer
Nick uses this
Watch Nick's video at 4:36“Keeps my queued filaments like PETG dry and ready, after humidifiers at home caused blobs and inconsistent layers.”
Specs
| Spools at once | 2 |
|---|---|
| Max heat | 80°C |
| Prints while drying | Yes |
| Spool turns freely | Yes |
| Humidity display | Yes |
| Power | 130 W |
| Timer up to | 24 hours |
From EIBOS's own pages. A spec EIBOS does not confirm is left out.
What it can dry
The Polyphemus filament dryer heats up to 80°C. Here is how that meets Bambu Lab's fan oven chart.
Reaches
- PLA50°C
- PETG65°C
- TPU70°C
Does not reach
- ABS and ASA85°C
- PC85°C
- Nylon and carbon blends85°C
Source: Bambu Lab Wiki: Drying filament, the fan oven column.
About the Polyphemus filament dryer
The EIBOS Polyphemus is a two-spool filament dryer with a motor that turns the spools while they dry, and a humidity mode that holds the box at a level you set. It heats to 80°C, feeds a printer through outlets in the case, and it's the dryer Nick has used for spools waiting their turn. It suits anyone who wants filament kept dry between prints, not only dried once.
Who it suits
Nick has used the Polyphemus himself. His verdict: "Keeps my queued filaments like PETG dry and ready, after humidifiers at home caused blobs and inconsistent layers."
The humidity mode is what suits that job. When heating isn't needed, you set a humidity level and the Polyphemus switches its heater on as needed to hold it, by EIBOS's description. An adjustable vent on top of the lid can be closed when you're not heating, and a separate compartment holds desiccant.
What to know before buying
EIBOS sends the hot air through several outlets rather than straight onto the filament, and added the rotating motor to even out the heat between the top and bottom of the chamber. Rotation starts with one button.
- Built-in settings cover nine materials: PLA, ABS, PA, PC, PETG, ASA, PVA, TPU and PP, plus three custom slots. Each sets temperature, time and heating power, and EIBOS says your settings are kept through a power cut.
- There are three heating power levels. EIBOS suggests full power for high-temperature materials such as PA, and low power for gentler drying of PLA with more precise temperature control.
- The temperature sensors sit inside the chamber, and the display switches between °C and °F and can show humidity.
- EIBOS says the casing uses V0 fire-rated material, and the dryer triggers an alarm and shuts down if its fan fails.
Filament outlets on the front and back of the case let you run filament to the printer without piercing or modifying the box, and EIBOS says a spool that's already threaded to the printer can go straight into the chamber. That matters on long prints. Bambu Lab's drying guide says that at around 55% humidity, freshly dried filament usually takes on enough moisture to affect print quality within 2 to 12 hours.
EIBOS also offers an expansion module that widens the chamber from 210 mm to 250 mm in diameter, for up to 3 kg of filament.
Drying engineering filaments
EIBOS puts ABS, ASA, PA and PC in the Polyphemus's built-in settings, and the dryer tops out at 80°C. Bambu Lab's drying chart gives 75 to 85°C for ABS, ASA, PC and fibre-filled nylons in a forced-air oven, so 80°C sits inside that range but short of its top. If those materials are most of what you print, a dryer that reaches 85°C covers the whole range. For PLA Basic at 50°C, PETG at 60 to 65°C and TPU at 70°C on the same chart, the Polyphemus has heat to spare.
Nick's video
Compare with similar dryers
The dryers nearest the Polyphemus filament dryer on spools and max heat.
| Dryer | Spools | Max heat | Prints while drying | Price | Nick |
|---|---|---|---|---|---|
| EIBOSPolyphemus filament dryer This dryer | 2 | 80°C | Yes | Amazon only | Uses it |
| CrealitySpace Pi V2 Plus Filament Dryer | 2 | 75°C | Yes | $89 | Not tested |
| SUNLUFilaDryer SP2 | 2 | 70°C | Yes | $69.99 | Not tested |
| SUNLUFilaDryer E2 | 2 | 110°C | Yes | $249.99 | Not tested |
| CrealitySpace Pi V2 Filament Dryer | 1 | 75°C | Unconfirmed | $66 | Not tested |
Store prices as of Nov 17.
More reading
- The best filament dryersNick's picks and how to choose one
- Filament deals: dryers and storageEvery dryer and storage item with today's price