Creality Space Pi V2 Plus Filament Dryer

Creality

Creality Space Pi V2 Plus Filament Dryer

2 spools · up to 75°C · humidity sensor · prints while drying · 48 h timer

Not tested by Nick

Specs

Spools at once2
Max heat75°C
Prints while dryingYes
Humidity displayYes
Timer up to48 hours

From Creality's own pages. A spec Creality does not confirm is left out.

What it can dry

The Space Pi V2 Plus Filament Dryer heats up to 75°C. Here is how that meets Bambu Lab's fan oven chart.

Reaches

  • PLA50°C
  • PETG65°C
  • TPU70°C

Does not reach

  • ABS and ASA85°C
  • PC85°C
  • Nylon and carbon blends85°C

Source: Bambu Lab Wiki: Drying filament, the fan oven column.

About the Space Pi V2 Plus Filament Dryer

The Creality Space Pi V2 Plus is the two-spool dryer in Creality's Space Pi line. It uses PTC heating, circulates hot air around the spools, and runs from a touch panel with one-key presets for up to 12 filament types. It can feed a printer while it dries, so it suits two printers running side by side, or one printer that swaps between two materials, mostly PLA, PETG and TPU.

How it feeds your printer

Each spool can stay in the box and feed the printer through a PTFE tube while the heater keeps running. Creality's own blog describes the Plus with two PTFE feed ports for printing while it dries. Bambu Lab's drying guide says that at around 55% humidity, freshly dried filament usually takes on enough moisture to affect print quality within 2 to 12 hours. On a long print, feeding from the dryer keeps the spool from sitting in room air for that long.

What to know before buying

  • The timer runs up to 48 hours, and power-off memory keeps your settings if the power goes off.
  • Creality lists a second-generation smart sensor and says the Plus works with more than one filament diameter.
  • The display shows real-time humidity, temperature and the timer.

Creality's own pages give two different top temperatures for the Plus, so neither is quoted here. Either figure reaches the 70°C that Bambu Lab's chart gives for TPU in a forced-air oven, and the 50°C for PLA and 60 to 65°C for PETG. If ABS, ASA, PC or nylon blends are most of what you print, look at a hotter dryer, since Bambu Lab's chart puts those at 75 to 85°C.

Once a spool is dry, it still needs somewhere sealed to live. Bambu Lab advises storing dried filament in a sealed container or an AMS with effective desiccant straight away, so plan for that if the Plus will dry more spools than it can feed.

The V2 or the V2 Plus

The Plus holds two spools and the V2 holds one. Creality's highlights for the two read the same on 360° hot-air circulation, the second-generation smart sensor and the smart presets with touch control, and the Plus adds a new air duct design. The Plus also ships in a bigger box. Creality lists its package at 343 by 226 by 300 mm and 2,500 g gross, against 315 by 125 by 300 mm and 1,450 g for the V2. Pick the Plus if you want both of your printers fed from one dryer.

Compare with similar dryers

The dryers nearest the Space Pi V2 Plus Filament Dryer on spools and max heat.

DryerSpoolsMax heatPrints while dryingPriceNick
CrealitySpace Pi V2 Plus Filament Dryer This dryer275°CYes$89Not tested
SUNLUFilaDryer SP2270°CYes$69.99Not tested
EIBOSPolyphemus filament dryer280°CYesAmazon onlyUses it
SUNLUFilaDryer E22110°CYes$249.99Not tested
CrealitySpace Pi V2 Filament Dryer175°CUnconfirmed$66Not tested

Store prices as of Nov 17.

Compare every dryer

More reading