
SUNLU
SUNLU FilaDryer S4
4 spools · up to 70°C · humidity control · prints while drying
Specs
| Spools at once | 4 |
|---|---|
| Max heat | 70°C |
| Prints while drying | Yes |
| Spool turns freely | Yes |
| Humidity display | Yes |
From SUNLU's own pages. A spec SUNLU does not confirm is left out.
What it can dry
The FilaDryer S4 heats up to 70°C. Here is how that meets Bambu Lab's fan oven chart.
Reaches
- PLA50°C
- PETG65°C
- TPU70°C
Does not reach
- ABS and ASA85°C
- PC85°C
- Nylon and carbon blends85°C
Source: Bambu Lab Wiki: Drying filament, the fan oven column.
About the FilaDryer S4
The SUNLU FilaDryer S4 is a four spool filament dryer built around one large heated chamber. SUNLU sizes it for four 1 kg spools at a time and says it can supply four printers at once while it dries, with multicolour printing and setups with several machines as the jobs it has in mind. Nick Nicholls uses one, and his verdict is short: "A great option if you run more than one printer."
How it feeds your printer
The S4 is made to keep drying while you print, so filament can run from the box straight to the machine. SUNLU packs two 100 cm PTFE tubes and four 8 cm tubes for routing it. It takes 1.75 mm, 2.85 mm and 3.0 mm filament, and SUNLU says it works with all printer models.
What to know before buying
The S4 tops out at 70°C, and SUNLU says it heats to 50°C in 30 minutes. Fans on the left and right of the chamber and a heating fan in the base keep the air moving, and SUNLU says that holds the temperature inside to within ±3°C so every part of the load dries evenly. There's also a humidity mode. You pick a target between 30% and 50%, the dryer starts when the box reaches it, and it runs until humidity falls to 25%.
It's a big box. SUNLU lists it at 458 by 218 by 312 mm including the height of its tripod, with 450 by 210 by 211 mm of space inside, and a net weight of 4.8 kg. SUNLU describes three layers of protection: the PTC heater, a temperature switch, and software that watches the temperature and gives an alarm prompt when it's abnormal. The warranty is one year, and it doesn't cover damage from a power supply that isn't the original or from not following the instructions. SUNLU's own S4 page gives more than one power figure, so this page doesn't print a wattage.
Compared with the rest of SUNLU's range
The S4 Pro keeps the four spool capacity and almost the same outside size, 458 by 218 by 310 mm, but splits the inside into two zones with their own temperature and time settings, raises the top heat to 85°C and adds an annealing mode. For nylon, PC and other engineering filaments, SUNLU's hotter options here are the S4 Pro, which it pitches at PA, PC and PP, and the two spool E2, which reaches 110°C. If one spool at a time is enough, the single spool S2 shares the S4's 70°C ceiling.
Nick's video
Compare with similar dryers
The dryers nearest the FilaDryer S4 on spools and max heat.
| Dryer | Spools | Max heat | Prints while drying | Price | Nick |
|---|---|---|---|---|---|
| SUNLUFilaDryer S4 This dryer | 4 | 70°C | Yes | $116.99 | Uses it |
| SUNLUFilaDryer S4 Pro | 4 | 85°C | Yes | $139.99 | Not tested |
| SUNLUFilaDryer SP2 | 2 | 70°C | Yes | $69.99 | Not tested |
| CrealitySpace Pi V2 Plus Filament Dryer | 2 | 75°C | Yes | $89 | Not tested |
| EIBOSPolyphemus filament dryer | 2 | 80°C | Yes | Amazon only | Uses it |
Store prices as of Nov 17.
More reading
- The best filament dryersNick's picks and how to choose one
- Filament deals: dryers and storageEvery dryer and storage item with today's price