
SUNLU
SUNLU FilaDryer S4 Pro
4 spools · up to 85°C · two heat zones · humidity control · prints while drying
Not tested by Nick
Specs
| Spools at once | 4 |
|---|---|
| Max heat | 85°C |
| Prints while drying | Yes |
| Spool turns freely | Yes |
| Humidity display | Yes |
| Power | 380 W |
From SUNLU's own pages. A spec SUNLU does not confirm is left out.
What it can dry
The FilaDryer S4 Pro heats up to 85°C. Here is how that meets Bambu Lab's fan oven chart.
Reaches
- PLA50°C
- PETG65°C
- TPU70°C
- ABS and ASA85°C
- PC85°C
- Nylon and carbon blends85°C
Source: Bambu Lab Wiki: Drying filament, the fan oven column.
About the FilaDryer S4 Pro
The SUNLU FilaDryer S4 Pro is a four spool filament dryer split into two chambers, each with its own temperature and time setting. SUNLU's example is drying PLA or PETG on one side while conditioning PA, PC or PP on the other. It heats to 85°C, adds an annealing mode for printed parts, and SUNLU pitches it at home studios, workshops and print farms.
Drying engineering filaments
The 85°C ceiling puts the S4 Pro above SUNLU's 70°C dryers. SUNLU lists PLA, PETG, TPU, ABS, ASA, PA (nylon), PC and versions filled with carbon fibre or glass fibre as compatible. The annealing mode is meant to improve the strength, dimensional stability and heat resistance of finished parts, and SUNLU names PA, PC and PP as well as parts in engineering materials with an annealing temperature of 85°C or less. For anything that needs more heat than that, SUNLU's E2 goes to 110°C.
What to know before buying
SUNLU lists each chamber at 220 by 210 by 211 mm and sizes the whole dryer for four 1 kg spools. Outside it measures 458 by 218 by 310 mm and weighs 4.7 kg, and SUNLU gives its rated power as 380 W. Humidity can be left to the dryer. You set a target between 30% and 50%, it starts when the chamber reaches that level and stops at 25%. Each zone has its own time control, but SUNLU's page doesn't give the timer's range.
Filament can feed a printer from the box while it dries. The package holds a power cable, the user manual, two 1 m PTFE tubes, an accessory kit, eight stainless steel shafts and 16 bearings. SUNLU sells US, EU and AU plug versions, with power input listed as AC 110 V at 60 Hz or AC 220 V at 50 Hz.
Compared with the rest of SUNLU's range
The original S4 has the same four spool capacity in nearly the same footprint, 458 by 218 by 312 mm, but uses one chamber and tops out at 70°C. The second zone, the annealing mode and the extra 15°C are what the Pro adds. The E2 holds two spools rather than four but reaches 110°C, so it's the SUNLU option here above the S4 Pro's 85°C limit. The single spool S2 and the two spool SP2 both stop at 70°C, like the S4.
Compare with similar dryers
The dryers nearest the FilaDryer S4 Pro on spools and max heat.
| Dryer | Spools | Max heat | Prints while drying | Price | Nick |
|---|---|---|---|---|---|
| SUNLUFilaDryer S4 Pro This dryer | 4 | 85°C | Yes | $139.99 | Not tested |
| SUNLUFilaDryer S4 | 4 | 70°C | Yes | $116.99 | Uses it |
| EIBOSPolyphemus filament dryer | 2 | 80°C | Yes | Amazon only | Uses it |
| CrealitySpace Pi V2 Plus Filament Dryer | 2 | 75°C | Yes | $89 | Not tested |
| SUNLUFilaDryer SP2 | 2 | 70°C | Yes | $69.99 | Not tested |
Store prices as of Nov 17.
More reading
- The best filament dryersNick's picks and how to choose one
- Filament deals: dryers and storageEvery dryer and storage item with today's price