SUNLU FilaDryer E2

SUNLU

SUNLU FilaDryer E2

2 spools · up to 110°C · humidity sensor · prints while drying · 99 h timer

Not tested by Nick

Specs

Spools at once2
Max heat110°C
Prints while dryingYes
Humidity displayYes
Timer up to99 hours

From SUNLU's own pages. A spec SUNLU does not confirm is left out.

What it can dry

The FilaDryer E2 heats up to 110°C. Here is how that meets Bambu Lab's fan oven chart.

Reaches

  • PLA50°C
  • PETG65°C
  • TPU70°C
  • ABS and ASA85°C
  • PC85°C
  • Nylon and carbon blends85°C

Source: Bambu Lab Wiki: Drying filament, the fan oven column.

About the FilaDryer E2

The SUNLU FilaDryer E2 is a two spool dryer that heats to 110°C and doubles as an annealing chamber. SUNLU describes it as made for engineering materials, with drying and annealing in one machine, and lists ABS, ABS-CF, ASA, PC, flame retardant PC, PC-ABS, PC-PBT, CoPA, PA6-GF, PA6-CF, PA12-CF, PA612-CF and PA12 among the materials it suits for annealing. It's aimed at people printing functional parts in those materials, though SUNLU says it handles conventional filaments too.

Drying engineering filaments

SUNLU says the E2 takes 20 minutes to reach 50°C from room temperature and 30 minutes to reach 70°C, with 110°C as the top setting. For sealing and insulation, the filament hole has a one piece silicone plug, the cover has silicone sealing strips to keep outside moisture out, and the insulation is double layered. SUNLU says that with more than 100°C inside, the outside stays below 60°C to the touch. A two level temperature control switch cuts out if the dryer overheats and resets once it cools.

Annealing is the other half of the job. SUNLU says it improves the impact resistance and durability of engineering material parts, and gives drone accessories, helmets, screws and nuts, and blower pipes as examples of parts that benefit. There are built in presets for different filaments, each applied with one click.

What to know before buying

  • Your spool has to take the heat. SUNLU warns that high temperature drying has to allow for the temperature resistance of the filament spool itself, so check yours before running near the top of the range.
  • Spool size. The largest spool it takes is 250 mm across and 153 mm wide. SUNLU tested two 1 kg, two 2 kg or one 3 kg spool, using its own spools, and says other brands differ slightly but basically fit.
  • Feeding while printing. Filament can run to the printer while it dries. It takes 1.75 mm and 2.85 mm filament, and the included PTFE tubing is 4 by 3 mm, in two 8 cm and two 1 m lengths.

Compared with the rest of SUNLU's range

The E2 is the hottest of SUNLU's dryers here. The S4 Pro holds four spools in two independent zones and also anneals, but tops out at 85°C, and SUNLU pitches its annealing at PA, PC and PP and at parts in materials with an annealing temperature of 85°C or less. The S4, S2 and SP2 all stop at 70°C. If your filaments need more than 85°C, the E2 is the SUNLU model here that reaches it.

Compare with similar dryers

The dryers nearest the FilaDryer E2 on spools and max heat.

DryerSpoolsMax heatPrints while dryingPriceNick
SUNLUFilaDryer E2 This dryer2110°CYes$249.99Not tested
EIBOSPolyphemus filament dryer280°CYesAmazon onlyUses it
CrealitySpace Pi V2 Plus Filament Dryer275°CYes$89Not tested
SUNLUFilaDryer SP2270°CYes$69.99Not tested
ElegooH1 HT Dryer Box185°CYes$80Not tested

Store prices as of Nov 17.

Compare every dryer

More reading